This is my first tutorial and it's kind of long, so bear with me. I used the pre-cut pieces of acrylic felt as that was what I had on hand, but you can use wool felt or fleece, anything that has some thickness and doesn't fray.
Felt scraps for toppings
5. Cut a piece of red felt to fit in the flat middle part of your pizza crust. Glue in place. Cut a slightly smaller irregular circle of white felt for your cheese. Glue this in place too.
6. Cut toppings from your scraps. I made a green pepper, olive, and mushroom pizza. Glue these in place however you like.
Ta-da!, your pizza flowers are all done! Now time to make some buds to fill out the plant...
1. Cut out some smaller circles from your left over beige and red felt. Cut as many circles as you want buds.
2. Cut a slice from each circle, maybe a sixth of the circle. Cut slightly more from the red than the beige.
3. You can make a tightly closed bud by rolling and gluing the red piece. Make sure it flairs out a bit at the end, but is tight at the point. Wrap and glue the beige piece over it.
4. To make a more open bud, cut some stips of white felt about 3" long. Stack two of them together and take a stitch through the middle of the strip. Sew this to the center of your red piece. This will give you little cheese "stamens". You can add some longer, thinner toppings too if you like (slices of green pepper, etc). Then make them the same as the tight bud, just don't roll as tightly.
1. Cut a simple leaf shape from your cardboard to make a template.
2. Stack two piece of green felt together and trace your template as many times as you can. Also draw a line up the center of each leaf.
3. Starting near your center line, sew up along the center of the leaf. You can pivot and sew towards the edge and then back to make little veins. Once you get close to the top of the leaf, pivot and sew back down the middle of the leaf, slightly over from your first line of stitching (maybe 1/4"). This will create a channel along the center of the leaf, about 1/4" wide. Use the picture to kind of give you a better idea of what to do. The arrow indicates the opening of the channel.
4. When you get to the base of the leaf again, sew around the edge of the leaf and back to where you started. Make sure you do NOT sew over the opening to the channel.
5. Cut each leaf out close to the sewing line.
6. Cut a piece of wire about 3 times the length or your leaf. Fold it in half and feed it into the channel. This makes it so you can pose your leaves.
7. Repeat for as many leaves as you want, making them various sizes. Also cut out several small leaves from a single layer of felt (maybe 1 1/2" to 2" in length).
Now let's put it together!
1. Make your stems by first cutting a strip of felt wide enough to wrap around your pencil with some overlap and and a little longer than the pencil. You can cut the pencil down for shorter stems. Wrap the felt around and glue or whipstitch in place.
2. Snip into the extra felt to make several tabs at the top of the stem. Spread these out and glue to the back of your pizza flower.
3. Cut an irregular circle that is about an inch smaller than your pizza flower. Cut a slit into it that extends a little bit past the center. Make some little clips from the center. (Check out the picture.)
4. Wrap one of the little leaves you cut around the bottom of your pizza buds and glue in place. Trim away the extra and stitch or glue to your stem in little clusters. Glue on a few extra leaves. Make sure not to do it too close to the base so you'll be able to see them all.
5. Once you have all your pizza flowers ready, cut a piece of dark brown felt to line what you're planting them in. Trace the opening of your "planter" and cut out this piece. Cut slits where you want the plants to be and slide them in. Use your scraps from this project to stuff around the stems to give them some stability and slide them in. Glue leaves around the edge and bend them until you're happy with how they look.
All done! Sit your plant somewhere sunny and remember not to litter!